Skip to Main Content

Harvest Tips to Keep More Grain in the Tank

Author: Syngenta Agronomist

Categories: CORN PLANT DEVELOPMENT, HARVEST, CORN, SOYBEANS
Share:

A successful harvest is measured by more than speed. The right combine setup can help keep more grain in the tank, improve data quality and support better field conditions for next season. Here are some tips to help during this harvest season.

Identify Source of Grain Loss Before Adjusting

Combine harvesting corn in a field, illustrating where grain loss can occur during harvest Figure 1 Harvest loss before harvest, at header or during threshing / cleaning.

Start by identifying where grain is being lost. Grain on the ground before harvest or loss at the header will not be fixed by adjusting separation and cleaning settings. Identifying where losses are occurring helps focus adjustments where they can make a difference.

Loss can occur before harvest, at the header, or during threshing, separating and cleaning. Start by checking pre-harvest loss and comparing it to the loss behind the combine. The difference between the two can be attributed to threshing and cleaning adjustment losses. In corn, header loss may include dropped ears, missed ears or loose kernels caused by shelling at the corn head.

Put a Number on Harvest Loss

Crop1 bu./acre loss in
1 ft. × 1 ft.
1 bu./acre loss in
30 in. × 30 in.
Corn2 kernels12 kernels
Soybeans4 seeds25 seeds
Table 1. Calculated yield losses based on kernels on the ground.

Quantifying how much grain is on the ground is a quick way to put a dollar value on combine adjustments. Small amounts of grain can add up quickly across a field. Just two corn kernels per square feet is 1 bu/ac.

Use a simple counting method to put what you see behind the combine into perspective, and check several representative locations across the harvest width instead of relying on one spot. Remember to check in front of the combine to understand pre-harvest loss and behind the combine to evaluate machine losses. In addition, checking behind the outer header rows can help separate header loss from grain lost through the combine.

Don’t Set and Forget: Harvest Conditions Change Fast

Manufacturer-recommended settings are a good starting point when setting a combine, but they still need small incremental adjustments to match actual crop and field conditions. For example, small changes in corn cob diameter result in changes in concave settings.

When troubleshooting, change one setting at a time, evaluate the result and then make other adjustments if still needed. The correct setup at 11 a.m. may not be the correct setup at 3 p.m. as crop moisture, hybrid or variety, wind, lodging and residue conditions change throughout the day.

Since soybeans typically become drier later in the day, pod shatter can be a major source of loss if reel speed and position are not changed throughout the day. A common starting point is to operate the reel about 25% faster than ground speed and keep the reel height in the upper one-third of standing plants.

Newer combine automation systems can help monitor and adjust grain loss and quality. However, the best results still come from pairing technology with operator experience, grain checks and field observations. Pre-season calibration of sensors, clearances and displays helps ensure automation tools are ready to make better decisions during harvest.

Infographic showing soybean reel speed, header height and loss-check tips: run the reel about 25% faster than ground speed, harvest the upper third of standing plants, and recheck losses as conditions dry.Figure 2: Start with the recommended reel and header settings, then recheck soybean losses as field conditions change.

Collect Yield Data You Can Trust

Combine yield monitor displaying harvest data from the fieldFigure 3: A properly maintained and calibrated yield monitor helps collect reliable data for future field decisions.

Good yield data starts with a properly maintained and calibrated yield monitor. Take time before and during harvest to make sure the system is ready before relying on yield maps for future decisions.

Yield Monitor Accuracy Checklist

  1. Check clean-grain elevator chain tension.
  2. Inspect sensors for dirt and debris.
  3. Confirm the feeder house position switch is working.
  4. Keep camera lenses clean on camera-based automation machines.
  5. Verify the accuracy of the scale being used to calibrate the combine.
  6. Use multi-point calibrations (several loads at different grain flow rates):
    • Load 1: Slow speed / low grain flow
    • Load 2: Moderate speed
    • Load 3: Normal speed
    • Load 4: Fast speed
    • Load 5: Faster speed / High grain flow

Uniform Residue Sets Up Uniform Emergence Next Year

Harvest decisions can influence the field long after the combine leaves. Even residue spread helps create more uniform soil temperature and moisture conditions heading into spring. As headers continue to get wider, it becomes increasingly important for the combine to distribute residue evenly across the entire harvest width.

Uneven residue, especially heavy soybean residue, can leave thick bands that stay cooler and wetter than the rest of the field. Those areas can affect tillage performance, planter ride, seed depth, seed-to-soil contact and emergence uniformity the following season.

Achieving even spread becomes more challenging as wider draper heads are adopted. Consider:

  1. Knife Sharpness
  2. Chopper Speed (increase aggressiveness if residue is stringy or long)
  3. Higher Spinner Speed for wider harvest widths
  4. Proper Vane Settings

Your In-Field Harvest Checklist

A good harvest routine does not need to be complicated. Use this sequence as conditions change throughout the day:

  • ☑ Check pre-harvest loss.
  • ☑ Check header loss.
  • ☑ Check loss behind the combine.
  • ☑ Inspect grain quality.
  • ☑ Adjust one setting at a time.
  • ☑ Recheck losses and grain quality.
  • ☑ Calibrate yield monitors.
  • ☑ Check residue distribution.

The goal is not just to cover acres quickly, but to balance harvest capacity with grain loss, grain quality, data accuracy and residue placement. Small harvest checks can pay off by keeping more grain in the tank and creating better conditions for next year’s crop.

Because combine setup varies by machine model, crop conditions and harvest goals, growers should also consider contacting their equipment manufacturer or local equipment dealer for machine-specific recommendations. Dealer service teams and manufacturer support resources can help confirm baseline settings, troubleshoot recurring grain loss or grain quality issues, and identify adjustments that best fit the combine, header and field conditions.


X

You are viewing from

Thank you for visiting the Golden Harvest website. We understand how important it is for you to find agronomic and product information pertinent to your local area. Please enter your zip code or select your area below to ensure you are seeing the information that matters most to you.
Learn more about regions >

CHANGE BY ZIP CODE OR SELECT YOUR REGION

OR
We're sorry. Golden Harvest is not available in this area. Please try another zip code or contact a Golden Harvest Seed Advisor™ for more information.

Is this page helpful to you?

How can we improve
this page? (optional)

Can you tell us your
role in agriculture? (optional)

Thanks for the feedback.

We appreciate your participation